Commercial Refrigerant Leak Detection: US Owner Requirements
For covered US commercial stationary equipment, require leak location, repair, and initial and follow-up verification when the repair threshold is exceeded, unless the owner or operator elects a compliant retrofit or retirement instead; use an equipment-ID checklist to document those separate tasks. Applicability depends on refrigerant, full charge and appliance use. The owner’s checklist is recommended documentation, not a prescribed federal form. [2][3]

1. Identify the equipment before assigning a rule
Create a sheet for each equipment ID with its location, refrigerant or blend, documented full charge, appliance use and supporting nameplate or service information. These details support the applicability decision. [2][3]
- Commercial refrigeration: supermarket and restaurant refrigeration or cold storage for perishables. [1]
- Industrial process refrigeration: process-linked refrigeration, industrial ice machines or ice rinks. Under Section 608, mixed-use equipment belongs here when at least 50% of operating capacity serves industrial process refrigeration. [1]
- Comfort cooling: equipment controlling heat or humidity in occupied spaces, such as office-building chillers. [1]
Use the same equipment ID on the service scope, test results and refrigerant records.
2. Determine which federal requirements apply
The AIM Act leak-repair requirements began January 1, 2026. Keep them separate from Section 608’s provisions for qualifying ozone-depleting-refrigerant appliances. [2][3]
- HFCs or qualifying substitutes — AIM Act: The full-charge threshold is at least 15 pounds. Residential and light-commercial air-conditioning and heat-pump equipment is exempt from these provisions, as are appliances using an HFC substitute with an exchange value or global warming potential (GWP) of 53 or less. Covered equipment falls under 40 CFR Part 84, Subpart C. [2]
- Class I or Class II ozone-depleting refrigerants — Section 608: The full-charge threshold is at least 50 pounds, including blends containing either refrigerant class. These leak-repair provisions fall under 40 CFR Part 82, Subpart F and exclude appliances containing only substitute refrigerants, such as HFCs. [2][3]
Do not decide the AIM exemption from the building’s label. Chillers and certain variable-refrigerant-flow systems fall into separate subsectors; match the appliance itself to the subsector. [2]
If equipment falls outside these particular provisions, record that limited conclusion—not “exempt from refrigerant requirements.” Washington facilities also need the state-program check below. [2][3][4]
3. Calculate the leak rate and repair deadline
For covered appliances, adding refrigerant generally requires a leak-rate calculation, subject to specified exceptions; it does not automatically trigger mandatory repair. Request the addition date, pounds added, full charge, calculation method and resulting rate. [2][3]
The annualizing and rolling-average methods are distinct permitted choices, and method changes are restricted. Obtain the documented calculation rather than a shortcut based on the latest top-up. [2]
For appliances already determined to be covered, the repair-trigger thresholds are:
- Commercial refrigeration: 20%. [1][2][3]
- Industrial process refrigeration: 30%. [1][2][3]
- Comfort cooling and other covered categories: 10%. [1][2][3]
When refrigerant is added to an appliance exceeding its threshold, leaks generally must be identified and repaired within 30 days, or 120 days if an industrial process shutdown is required. Qualifying extensions may apply. Record the triggering addition date and deadline. [2][3]
Keep the calculated rate separate from detector readings or a “low refrigerant” observation: neither replaces the required calculation. [2][3]
4. Specify location, repair and verification separately
A leak search or recharge invoice is not proof of a completed repair. Covered repairs require initial and follow-up verification, not merely restored cooling. Put these deliverables in the scope: [2][3]
- Locate the leak. Request the leaking component and physical location. For Section 608 equipment, a certified technician must identify the location through a leak inspection. [3] Get Freon’s supplementary consumer guidance describes electronic detection, bubble testing and other methods; pressure or vacuum decay alone does not locate the escaping point. [6]
- Describe the repair. Request an account of what was repaired or replaced—not just inspection findings or refrigerant added. [3][6] Ask for the manufacturer-specific test procedure rather than a universal pressure or hold time. [6]
- Document initial verification. The initial test must occur within the applicable repair period. Request its date and result. [2][3]
- Complete follow-up verification. The test is due within 10 days after successful initial verification or, as applicable, within 10 days after the appliance returns to normal operating conditions. [2][3] Specify additional repairs and testing after failed tests within the applicable repair period. [2]
Trane describes certified mechanical-service technicians, refrigerant handling and monitoring capabilities on its commercial page. [5] Treat those vendor-reported features as a starting point, and request the location, repair and verification deliverables explicitly.
5. Separate monitoring from required inspections
Under Section 608, qualifying automatic leak detection can replace scheduled inspections for monitored portions if the system is audited or calibrated annually. Unmonitored portions remain subject to inspection, and repair-verification obligations remain. [3]
When the applicable leak-rate threshold is exceeded, set recurring federal inspections by appliance category and full charge:
- AIM commercial refrigeration and industrial process refrigeration, at least 500lb: inspect every three months until leak-rate calculations show four consecutive quarters without an exceedance.[2]
- AIM commercial refrigeration and industrial process refrigeration, at least 15lb but below 500lb: inspect annually until calculations show one year without an exceedance.[2]
- Section 608 commercial refrigeration and industrial process refrigeration: the corresponding charge bands are at least 500lb for quarterly inspections and at least 50lb but below 500lb for annual inspections, with the same four-quarter or one-year stopping criteria.[3]
- Covered comfort-cooling and other appliances outside those refrigeration categories: inspect annually until calculations show one year without an exceedance. Apply the AIM or Section 608 applicability test first.[2][3]
Recommended scope: Ask the contractor to map monitored and unmonitored portions and identify which inspections a proposed system would replace under the applicable rule. [3]
Trane says monitoring is required in certain buildings under ASHRAE 15, but its cited page does not state the standard’s criteria. Do not treat that vendor statement as a universal federal monitoring requirement. [5]
6. Track failed repairs and excessive losses
If an owner chooses retrofit or retirement, cannot identify or repair a trigger-exceeding leak, or remains above the threshold after required repair and verification, a plan is due within 30 days under the applicable federal rule. Completion generally must be scheduled within one year, subject to applicable exceptions. [2][3]
A Section 608 plan must identify the appliance and location, current and proposed refrigerant and full charge, conversion procedure, refrigerant and appliance disposition, and completion schedule. An authorized company official must sign and date it; keep it accessible at the appliance site, electronically or on paper, and available to EPA. [3]
Extensions are conditional. Document the qualifying basis, such as unavailable components or conflicting regulatory requirements. [1][3] Mothballing suspends applicable timelines; timelines resume on the day additional refrigerant is added to the appliance (or to the leaking component if it was isolated). [1][3]
Under AIM, a covered appliance leaking 125% or more of its full charge in a calendar year must be reported to EPA by March 1 of the following year. [2]
7. Add Washington requirements where applicable
Washington’s Refrigerant Management Program covers refrigeration and air-conditioning systems containing more than 50 pounds of refrigerant with GWP of at least 150. This is a state requirement, not a nationwide rule. [4]
For the Washington schedules below, identify the full refrigerant charge: large means at least 1,500lb; medium means 200–1,499lb; small means below 200lb within the program’s stated coverage threshold. Ecology categorizes a facility by its largest qualifying system. Check the system size separately when assigning its inspection frequency.[4]
Covered facilities must repair all leaks within 14 days of detection, check for leaks after repair and use EPA-certified technicians. A failed repair requires a retrofit and retirement plan unless an exemption is granted. [4]
- Large systems: Monthly inspections are required without automatic detection. Qualifying automatic detection was required by January 1, 2025, for specified enclosed high-leak-potential components. [4]
- Medium systems: Quarterly inspections took effect January 1, 2026; qualifying automatic detection removes the periodic-inspection requirement. [4]
- Small systems: Annual inspections begin January 1, 2028, except for systems with automatic leak detection that meets specifications. [4]
Registration deadlines were March 15, 2024, for large facilities and March 15, 2026, for medium facilities. Small facilities must register by March 15, 2028. Large and medium facilities begin annual reporting one year after registration; small facilities do not submit annual reports. [4]
Separate fee baselines from the amount due for a particular year. WAC 173-443-135 specifies a $150 initial implementation fee for qualifying facilities with a system of at least 1,500lb. It sets a $370 annual baseline beginning in 2024 for that size, but requires annual amounts from 2025 onward to be established under WAC 173-455-160. Do not budget $370 as a fixed current-year large-facility fee.[7]
For qualifying 200–1,499lb systems, the rule sets $170 annually beginning in 2026, with annual amounts established under WAC 173-455-160 from 2027 onward. Where a facility has several systems, the annual fee is based on its largest regulated system. The annual invoice is payable within 30 days of receipt; verify the invoiced year and applicable Ecology fee notice. Proposed fee formulas are not used here as amounts currently payable.[7]
Keep required records physically or electronically at the facility housing the systems for at least five years. [4]
8. Use an equipment-ID acceptance checklist
For each equipment ID, track the item, applicable rule, mandatory or recommended status, responsible party, due date and evidence received:
- Applicability — recommended worksheet: Record refrigerant identity, full charge, appliance category, exemption determination and federal/state rule assignment before approving the scope. [2][3][4]
- Additions and trigger — calculation mandatory when applicable: Capture quantities, dates, calculation method and calculated leak rate. Have the owner/operator obtain supporting service data. [2][3]
- Location and repair — mandatory when triggered: Request the named location, repaired or replaced component and completion date as acceptance evidence. Assign contractor delivery and enter the repair deadline. [2][3][6]
- Verification — mandatory when applicable: Obtain initial and follow-up test dates and results, plus repair and test records following failures. Assign contractor delivery and owner tracking. [2][3]
- Service quality — recommended: Request final refrigerant quantity and manufacturer-relevant operating observations at closeout. These are not universally mandated verification fields. [6]
- Ongoing duties — mandatory where applicable: Track inspections or monitoring, reporting, retrofit/retirement plans and Washington on-site retention duties. [2][3][4]
EPA’s fact sheet does not reproduce every required record field, but it states that owners or operators must maintain certain records for three years unless otherwise specified. [2][4] Use the checklist to connect the service evidence—not as a substitute for the applicable recordkeeping requirements.
References
- Stationary Refrigeration Leak Repair Requirements | US EPA (epa.gov)
- Leak Repair Requirements for Appliances Containing … (epa.gov, 2024)
- 40 CFR § 82.157 – Appliance maintenance and leak repair. | Electronic Code of Federal Regulations (e-CFR) | US Law | LII / Legal Information Institute (cornell.edu, 2019)
- Refrigerant Management Program – Washington State Department of Ecology (wa.gov)
- Refrigerant Management | Trane Commercial HVAC (trane.com)
- How to Check if an AC Refrigerant Leak Has Been Properly Fixed | Get Freon (getfreon.com, 2026)
- WAC 173-443-135 — Implementation fees (wa.gov, 2024)