Salt Spray Test Requirements for Australian Coated-Parts Buyers
To obtain comparable salt spray test quotes, specify the contractual exposure method, specimens, preparation, duration and assessment criteria; separate required work from conditional preparation and optional reporting requests. [2][3][4]

- Required by the contract or governing method: carry the specified method, edition, variant, exposure duration and acceptance criteria into the request. [3][4]
- Conditional preparation: settle masking, scribing, exposed areas and orientation where applicable—not as automatic steps for every specimen. [4]
- Additional requests: agree any extra observations, interim reporting and report deliverables with the laboratory. [2][4]
This is a purchaser’s ordering checklist, not a universal laboratory intake form. The published services distinguish exposure methods, specimen configurations and assessment activities. [2][3][4]
1. Translate the contract into an exact test method
Start with the governing customer specification, drawing or purchase requirement. Copy the standard designation, specified edition and test variant into the request rather than substituting another exposure. The published listings distinguish neutral salt spray from modified and cyclic exposures. [2][3][4]
- AS 2331.3.1: SIIGMATIC identifies this as its neutral salt spray method. [2]
- ASTM B117: Materials Performance Laboratory’s NATA scope lists this separately from modified salt spray under ASTM G85-02, limited to A5. [3]
- ASTM D5894: the scope separately lists cyclic salt fog/UV exposure, alternating between fog/dry and UV/condensation cabinets. [3]
Compeng describes neutral salt spray using a 5% salt solution with pH maintained between 6.5 and 7.2 and a chamber temperature of 35 °C. [4] Follow the specified option rather than treating a more aggressive exposure as an equivalent substitute. [4]
If the contract says only “salt spray”, obtain clarification from whoever controls the requirement before comparing quotes. Have the standard, edition and variant settled so laboratories quote the same exposure rather than different methods under one broad label. [2][3][4]
2. Match the work to the laboratory’s NATA scope
Match the requested work to the laboratory’s site-specific NATA scope, not a general accreditation claim. Materials Performance Laboratory’s Clayton scope provides an example under ISO/IEC 17025 (2017). [3]
- Locate the site. NATA lists the Materials Performance Laboratory at Gate 5, 2 Normanby Road, Clayton, VIC 3168. [3]
- Match the coating category. Its ASTM B117 and AS 2331.3.1 entries both cover architectural, decorative, industrial and marine coatings, and protective coatings on wooden furniture. The categories are the same for both entries. [3]
- Read every limitation. The modified salt spray entry is ASTM G85-02, A5 only. Other G85 variants are outside that displayed entry; check the scope when placing the order. [3]
- Check assessment coverage separately. The scope lists individual methods for degree of corrosion, blistering, cracking, flaking and peeling. Exposure coverage does not establish coverage for every requested assessment. [3]
Keep service listings and accreditation evidence separate. SIIGMATIC offers to confirm whether a requested method falls within its current NATA scope. [2] Compeng lists testing methods, while LMATS states general accreditation credentials; their cited pages do not independently establish method-specific salt spray accreditation. Request the relevant scope entry before relying on accredited coverage. [4][5]
NATA lists accelerated weathering of prepared test specimens under ISO 4892-2, SAE J1885 and SAE J1960 within the Materials Performance Laboratory’s scope of accreditation, not as certification of the coated product. [3]
3. Identify the coating, substrate and specimens
Name the coating or finish, metallic substrate and specimen configuration: test panels, complete components or partial assemblies. These distinctions appear in the published services and scopes. [2][3][4] SIIGMATIC lists complete or partial hardware assemblies and comparisons of alternative coatings. [2]
For assembled parts, describe the relevant joints, interfaces and mounting arrangements to preserve. [1][2] A 2014 NASA investigation indexed by Science.gov illustrates the principle: it tested connectors mounted to an aluminium bracket, using mounting techniques and materials representative of their intended use. This was a US investigation, not an Australian testing requirement. [1]
Use a specimen identification schedule to link each part’s identifier to its coating, substrate and configuration. This suggested organising aid lets the request distinguish the specimens and the observations wanted for each; it is not a published mandatory intake rule. [2][3][4]
Where relevant, propose specimen count, dimensions, coating thickness and application or cure history as supporting information. Agree these additional fields with the laboratory rather than treating them as a universal required specimen-information checklist. [2][3][4][5]
4. Agree preparation before shipping specimens
Agree specimen alterations explicitly. Compeng’s ISO 9227-based example includes tape protection and a scribe through the coating to expose the metal substrate, but it says the process may change with the applicable standard, product or test requirement. Masking and scribing are therefore not established as mandatory for every test. [4]
Separate preparation instructions into three groups:
- Specified preparation: identify masking, scribing, exposed-area and orientation instructions imposed by the governing method or contract, with the relevant requirement reference. [4]
- Specimen-specific instructions: record proposed masking, exposed areas or positioning needing agreement. Flag unresolved instructions rather than silently choosing a preparation approach. [4]
- Additional preparation: list proposed conditioning, sanding or solvent cleaning separately. Materials Performance Laboratory’s NATA scope includes particular controlled-condition and panel-preparation activities; their inclusion is not an instruction to apply them to every specimen. [3]
Resolve uncertainties before shipment. SIIGMATIC invites purchasers to discuss uncertain specimens, methods or scope with the laboratory before sending parts. Use that discussion to settle preparation instructions as well as test capability. [2]
5. Nominate duration and observation intervals
Record exposure duration separately, using the period required by the governing specification. SIIGMATIC describes exposure for a nominated period. Compeng gives examples of 24 hours, 72 hours or more than 1,000 hours, depending on the test requirement—not recommended packages or universal pass marks. [2][4]
- Exposure duration: state the required hours and the specification clause they come from. [2][4]
- Final assessment: nominate the assessment after the stipulated exposure and agree its reporting scope before testing. [2][4]
- Interim observations or reports: list requested intervals separately, distinguishing contractual requirements from additional requests subject to laboratory agreement. [2][4]
The cited SIIGMATIC and Compeng pages state neither a standard interim-reporting schedule nor a total service turnaround. Do not treat chamber exposure hours as a promised report-delivery time. [2][4]
6. Define the observations and report deliverables
Specify observations separately from the exposure method. Materials Performance Laboratory’s NATA scope lists coating assessments as distinct activities from salt spray exposure; SIIGMATIC identifies corrosion, blistering and coating breakdown as possible subjects for agreed post-exposure reporting. [2][3]
- Corrosion: request the relevant assessment and agree its method. NATA’s scope includes a separate degree-of-corrosion method. [3]
- Blistering: include it where relevant to the requirement, with the assessment method agreed; it is separately listed in the scope. [3]
- Coating breakdown: document corrosion, blistering, coating breakdown or other agreed observations. [2]
- Other observations: select cracking, flaking, peeling, discolouration, chalking or appearance where relevant—not as a mandatory assessment bundle. These are separately listed assessment activities. [3]
Request specimen-level identification and any desired photographs, observation tables or formal compliance statement in the reporting scope. Ask the laboratory to confirm which requested report fields it will provide. [2][3][4][5]
Recording a coating change does not supply the contractual limit against which it should be assessed. Keep reporting instructions separate from acceptance criteria. [2][4]
7. Assess results against the purchaser’s criteria
Compeng’s described process assesses corrosion against the specification’s acceptance criteria, not exposure hours alone. Supply the applicable contractual limits so results can be judged against the requirement. [4]
For each relevant observation, use an assessment entry linking the following fields. This is a suggested format, not a universal laboratory form. [2][3][4]
- Observation: name the coating change to be assessed.
- Assessment method: record the agreed method.
- Contractual limit and specification reference: state the acceptance limit and its governing reference.
- Applicable area: identify the specimen area to which the assessment applies.
- Assessment point: state when the assessment is required.
Obtain the applicable limits for rust area, blister size, scribe creep, cracking, adhesion loss or cosmetic change from the purchaser’s contract or referenced specification. [2][3][4][5]
When reading the report, distinguish completion of the nominated exposure, recorded coating changes and comparison with the stated acceptance criteria. Completion alone does not establish compliance. [2][4]
Controlled salt spray cannot reproduce every service environment. Do not convert exposure hours directly into years of Australian coastal service. [2][4]
8. Send the same written scope to each laboratory
Use this purchaser checklist to keep quotations aligned. Retain unresolved fields for clarification rather than allowing each laboratory to assume a different scope. [2][3][4]
Salt spray test request
- Contractual requirements: record the governing specification and revision; exact exposure method, revision and variant; exposure duration; required assessment methods; and purchaser’s acceptance criteria and clause references. [3][4]
- Specimen description: identify the coating/finish and substrate, specimen identifiers, whether specimens are panels, complete parts or partial assemblies, and any interfaces and mounting arrangements to preserve. [1][2][3][4]
- Conditional preparation: specify masking, scribing, exposed areas and orientation. Identify which instructions come from the governing requirement and which need agreement. [3][4]
- Additional requests: list observation intervals beyond those specified, extra assessments or observations, and report deliverables. Distinguish optional requests from contractual requirements. [2][3][4]
Obtain purchaser clarification for unresolved or conflicting contractual fields and laboratory confirmation for capability, preparation or reporting questions before sending specimens. SIIGMATIC specifically offers pre-shipment discussion where the specimen, method or scope is uncertain. [2][4]
Compare quotations after resolving differences in method, variant, preparation, exposure and reporting. Separately verify that any required accreditation covers the requested activities and limitations. [2][3][4]
References
- salt spray test: Topics by Science.gov (science.gov, 2014)
- Corrosion & Salt Spray Testing | SIIGMATIC (siigmatic.com.au)
- Materials Performance Laboratory – Accredited Organisation (Site No. 212) – NATA (nata.com.au)
- Salt Spray Testing Melbourne | Salt Fog Corrosion Testing (compeng.com.au)
- Salt Spray Test / Corrosion – LMATS (lmats.com.au)