Mobile Column Lifts: Requirements for US Truck and Bus Shops
Start with a vehicle-and-bay requirements checklist
Before accepting a mobile column lift proposal, require a documented match for each wheel-position load, wheel engagement, bay, floor and electrical supply; separate optional equipment from requested dealer services. Use these as purchasing conditions, not as a statement of legal requirements. [1][2][3]

- Essential suitability checks: Individual-column capacity, wheel and fork compatibility, operating clearances, floor suitability and power.
- Optional equipment: Identify accessories separately, but make any accessory needed for fleet compatibility part of the required package.
- Requested dealer services: Specify commissioning, operator instruction, handover records and support in writing rather than assuming the equipment price includes them.
John Bean’s May 2022 North American sell sheet and Stertil-Koni’s ST 1085/ST 1100 brochure, marked 02-2017, are older specification references, not confirmation of the equipment offered today. Use them to screen proposals, then obtain exact-model documentation. [2][3]
Build a worksheet with a row for each relevant vehicle configuration and a separate workshop checklist:
- Vehicle inputs: Record documented wheel-position loads, supporting axle information, tire outside diameter, rim size and the proposed column assignment at each position.
- Workshop inputs: Record bay dimensions, overhead obstructions, door openings, floor-assessment status, electrical supply, and storage or charging space.
- Review responsibility: Identify the manufacturer and qualified shop professionals who will resolve suitability questions before acceptance.
The equipment documents do not supply the fleet’s loads, wheel inventory, bay measurements or floor assessment. Those inputs must come from the workshop and its qualified reviewers. [1][2][3]
Match each column to its assigned wheel-position load
John Bean’s sell sheet lists choices of 12,000, 16,000 or 18,000 lb per column. These are the sheet’s published ratings; confirm the rating of the exact proposed model. [3]
Multiplying a per-column rating by the column count does not establish suitability when wheel-position loads are unequal. The manufacturer documents provide no load distribution, center-of-gravity information or permissible-imbalance assessment for the workshop’s vehicles. [1][2][3]
Do not treat an equal division of gross vehicle or axle weight as a verified wheel-position load. Obtain documented loads and a suitability assessment for the intended configuration. [1][3] For every assigned wheel position, record:
- Vehicle and configuration: Identify what the load information covers.
- Wheel position: Identify the position assigned to the column.
- Documented load: Record the supported value and its source—not an assumed equal share.
- Column model and rating: Record the exact model and individual-column capacity.
- Suitability confirmation: Request written manufacturer confirmation covering the configuration and column assignment.
Make missing load information a purchasing hold point. A headline set capacity cannot resolve an undocumented wheel-position load. [1][2][3]
Keep rim, tire and fork measurements separate
A capacity match leaves a separate question: does the proposed fork arrangement fit the wheel? Compare these dimensions without treating their ranges as interchangeable. [1][2][3]
- Rim diameter: Stertil-Koni’s ST 1085/ST 1100 brochure lists a standard rim range of R12–R22.5. Obtain exact-model confirmation before relying on this older specification. [2]
- Tire outside diameter: John Bean’s sell sheet lists a 22–59 in adjustment range for its universal carriage, which accommodates tires up to 59 in without extra accessories—not a rim-diameter range. [3]
- Adjustable-fork range: Stertil-Koni’s brochure separately lists 9⅜–22 in of fork adjustment. Do not substitute this dimension for its rim range or a tire outside-diameter limit. [2]
- Fork length: John Bean lists standard forks measuring 13 in long, a separate specification from the carriage’s accepted tire-diameter range. [3]
Stertil-Koni’s product page describes optional extra-wide forks accepting wheels up to R24.5 and tire outside diameters up to 63 in, limited to ST 1065, ST 1082, ST 1085 and ST 1100. ST 1082 appears in that option list but not in the page’s principal model table; request written compatibility confirmation for the quoted model. [1]
Attach a fleet wheel-fit schedule to the proposal. For each vehicle and wheel position, record rim and tire dimensions alongside the quoted column, standard or optional forks, fork adjustment and fork length. Ask the manufacturer to confirm the engagement arrangement; published dimensions alone do not establish suitability for the fleet’s wheels. [1][2][3]
Match the equipment and raised vehicle to the bay
The ST 1085/ST 1100 brochure lists a 97-in column height and 73-in maximum lift height; John Bean’s sell sheet lists a 69-in lift height. These are model-specific dimensions, not interchangeable measures of bay clearance. [2][3]
Column height describes the equipment’s vertical envelope; lift height describes its lifting travel. Neither alone establishes clearance for the raised vehicle. Use both as inputs to the bay assessment. [2][3]
Provide the manufacturer and qualified shop professionals with:
- Measured overhead obstructions and door openings.
- The vehicle envelope, including roof-mounted equipment where present.
- Proposed column locations and available space around the vehicle.
- A qualified floor assessment for those locations.
- Storage and charging locations.
Keep floor suitability separate from mobility. Stertil-Koni’s cited brochure does not state a required slab specification or floor-load rating. [1][2]
Stertil-Koni reports that optional retractable wheels reduce floor surface pressure; that claim is not approval of an existing floor. Have qualified shop professionals assess the actual floor against the proposed equipment and use conditions rather than deriving a floor design from the sales specifications. [1][2]
Confirm power and charging for the quoted configuration
A wireless or battery-powered description is not enough to establish electrical compatibility. Stertil-Koni and John Bean describe battery operation alongside different electrical specifications. [2][3]
- Stertil-Koni ST 1085/ST 1100, wireless: The brochure lists 24 VDC operation, with rechargeable batteries charged from a 110 VAC wall receptacle. [2]
- Stertil-Koni ST 1085/ST 1100, cabled: Listed options are three-phase 208/230, 460/480 or 575 VAC, and single-phase 220 VAC. Match the quoted version to the available supply. [2]
- John Bean: The sell sheet describes wireless operation using a 24 V rechargeable battery. It separately lists 2 hp, 208–230 V or 440–480 V, 60 Hz, three-phase requirements; do not assume every listed requirement applies to every variant. [3]
Request electrical documentation for the exact configuration, including its charging arrangement. Have a qualified electrical professional confirm compatibility with the workshop’s supply and obtain manufacturer clarification where the configuration’s requirements remain ambiguous.
Separate standard controls from accessories
Require an itemized quote identifying column count, exact model, control configuration and accessories—not just a package name. Keep equipment, accessory and dealer-service charges on separate lines.
For each item, record whether it is standard or optional, its model compatibility, the supplied quantity and any unresolved inclusion. This creates a usable comparison even when proposals use different package descriptions.
Stertil-Koni’s brochure documents a touchscreen control box at each column, Single/Pair/All modes, synchronization, overload protection, emergency stop, hold-to-run operation, and maintenance and fault displays. Check the proposed configuration against these features rather than accepting “standard safety controls” as a complete description. [2]
- Stertil-Koni options: Distinguish extra-wide forks, a lowered base frame, forklift adapters, retractable wheels and model-dependent drive-over cable accessories from universal inclusions. Record compatibility and quantity for each selected item. [1][2]
- John Bean options: The sell sheet lists a crossbeam with adjustable lifting pads, tripod support stands, a light-vehicle adapter, forklift ramp adapter, small-wheel adapters and remote control as optional accessories. [3]
If fleet compatibility depends on an accessory, make its inclusion an acceptance condition. Keep discretionary extras separately priced and carry commissioning and training into service line items.
Put dealer commissioning and handover in writing
Factory testing is not a dealer-handover commitment. Stertil-Koni’s brochure says each column is tested before leaving the factory and after-sales service is provided through factory-trained local partners. [2]
Ask Stertil-Koni and John Bean to define dealer commissioning procedures, acceptance-test records, a US service-response commitment and an operator-training package in writing. [1][2][3]
Make these requested contractual deliverables rather than presumed manufacturer requirements. Ask the dealer to attach a handover schedule covering:
- Responsibility and scope: Name the responsible dealer, included setup and commissioning work, who performs it and when handover occurs.
- Acceptance checks: Specify manufacturer-directed checks and records, including resolution of vehicle-fit and bay-suitability questions by the manufacturer and qualified shop professionals.
- Operator instruction: Define the instruction included, who delivers it and the completion record supplied.
- Equipment and documents: Request an inventory identifying models, individual columns and accessories, plus operating and maintenance documentation.
- Support and warranty: Identify service contacts, escalation arrangements, agreed response terms, warranty coverage, exclusions and claim procedures.
Keep warranty wording precise: Stertil-Koni’s published lifetime parts guarantee covers the synthetic runner wheels within the column—not the entire lift. [2] Put charges and exclusions beside the relevant equipment or service line item.
Close the proposal with an evidence checklist
Use these purchasing gates—not an official approval form—to make the acceptance decision:
- Wheel-position capacity: Document each assigned load and its matching column rating.
- Wheel engagement: Confirm wheel, tire and fork compatibility, including required accessories.
- Bay and floor: Obtain qualified suitability findings for clearances and the floor.
- Power: Document the configuration’s match to the supply and charging arrangements.
- Equipment and handover: Agree on included equipment, commissioning, instruction, records and support.
For each gate, record the supporting document, responsible reviewer and unresolved question. Mark the proposal ready for the purchasing decision when every gate is resolved, clarification required when evidence is missing, or unsuitable as proposed when a documented mismatch remains.
References
- Mobile Column Lifts | Stertil-Koni USA (stertil-koni.com)
- MOBILE COLUMN LIFT (stertil-koni.com)
- MOBILE COLUMN The John Bean® Mobile Column Lift System (johnbean.com)