HROUS

Hiring an Irrigation Auditor: Requirements for US Facility Managers

Advertisement

When hiring an irrigation auditor, specify zone-by-zone coverage, baseline measurements, separate repair and scheduling recommendations, and follow-up checks before approving controller replacement. DOE’s irrigation guidance identifies scheduling, repair and technology replacement as separate improvement pathways. [3]

Advertisement
A picturesque valley with irrigation under the warm sunset glow, capturing serene nature.

Distinguish program requirements from the deliverables you purchase:

  • Program requirements: Apply within the named program and version. EPA’s 2009 new-home audit guidelines belong to the historical Version 1 framework, not a universal standard for existing facilities. [2][6]
  • Purchased deliverables: Put the zone map, baseline records, prioritized corrections and follow-up measurements in the written scope rather than assuming every audit includes them. [1][3]
  • Applicable obligations: Verify state and local requirements separately; EPA’s commercial-facility guidance is voluntary, not a federal irrigation-efficiency standard. [1]

Check the program version first. EPA states that WaterSense Homes Version 1 was in effect from 2009 through 2021 and Version 2.0 took effect in February 2021. Version 2.0 addresses whole-home water efficiency for single-family homes and multifamily buildings. Its at-least-30-percent improvement concerns the home overall, not an irrigation-only pass mark. For a current certification project, establish the applicable Version 2.0 certification method and requirements rather than importing the older audit thresholds. [6]

Advertisement

Agree which areas and zones are in scope

Request a zone-by-zone coverage list in the proposal. “Irrigation audit” alone does not describe which areas will receive operating observations, pressure measurements or distribution testing. Make the planned assessment explicit. [1][2][3]

Request these fields for every zone:

  • Zone ID and mapped location: Use a consistent reference to connect findings, repairs and follow-up results.
  • Landscape area: Identify turf, planting beds, trees, narrow strips and slopes, including adjacent pavement and other non-target areas. [2][3]
  • Irrigation type: Identify spray, rotor and drip/microirrigation separately. [2]
  • Inspection or measurement: Distinguish operating observations, pressure readings and catch-can testing rather than labeling everything “tested.” [2]
  • Exclusions: Mark untested zones and inaccessible areas.
Advertisement

Include a hydrozone review: ask whether areas grouped for watering have compatible plant water needs, considering soil, sun, shade, wind and slope. A location label alone does not address those design considerations. [3]

EPA’s 2009 Guidelines for Irrigation Audits on WaterSense Labeled New Homes illustrates why testing scopes matter. That historical document called for pressure measurements on a representative zone of each irrigation type, but limited its catch-can threshold test to turfgrass in the largest spray-irrigated area. Those are different assessments—not evidence every zone received equivalent evaluation. [2]

EPA’s commercial-facility guidance and DOE’s guidance do not establish a universal whole-facility zone count or sampling percentage. Specify the coverage you want purchased, and do not treat a turf catch-can result as an assessment of drip delivery. [1][2][3]

Advertisement

Record the baseline before settings or equipment change

Require a before-change baseline linked to the zone map, not only a summary of adjustments made. EPA calls for assessment of the system, performance and schedule; make the following records explicit contract deliverables. [1]

  • Map and dated observations: Locate findings by zone and record leaks, misaligned heads, coverage gaps and runoff. The map establishes location; observations document visible problems. [1][3]
  • Existing controller settings: Record runtimes, watering frequency, start times, seasonal adjustments and sensor configuration before changes. These document the amount-and-timing choices to assess against climate, soil, plants, grading and season. [1][3]
  • Pressure readings: Request the measurement location, irrigation type, reading and manufacturer specification together so the report shows how operating pressure compares with equipment requirements. [1][3]
  • Catch-can records: Where tested, retain individual collection measurements and reported distribution results, identified by area—not merely a statement that coverage was checked. [1][2]

Request test dates, operating conditions and relevant weather context, including wind. EPA identifies environmental influences on performance, and DOE includes prevailing wind in design review. [1][3]

Include available dedicated irrigation-meter records and water-use trends. EPA recommends dedicated metering and retaining trends; use that history as baseline context, not proof a single observed defect caused all excess consumption. [1]

Advertisement

Read catch-can findings without overextending them

Ask for a traceable catch-can result: the tested zone or area, method, individual collection measurements and reported distribution result. Put these reporting terms in the scope rather than accepting an unexplained “pass.” [1][2][3]

A 65% result is not a universal passing grade for an existing facility. The 2009 Version 1 new-home audit guidelines required lower-quarter distribution uniformity (DULQ) of at least 65% under that historical single-family new-home specification. This is an example of a version-specific criterion, not a statement of the current Version 2.0 certification threshold. The old turfgrass test also did not establish performance in planting beds, drip zones or the entire property. [2][6]

Advertisement

Read uneven collections alongside head-to-head coverage, nozzle compatibility, operating pressure, wind exposure, runoff and overspray. These conditions can explain poor distribution; the result should not automatically be attributed to controller settings. Head-to-head coverage means water from one sprinkler reaches adjacent sprinklers. [1][3]

Also distinguish distribution testing from runtime checking. EPA’s Find It, Flag It, Fix It checklist describes timing how long multiple cans around a lawn take to collect one-half inch. That check helps estimate runtime for a locally recommended watering amount; it does not calculate DULQ. [5]

Neither agency supplies a universal existing-facility passing percentage or general catch-can calculation, spacing and test-duration protocol. Require the report to name its method and tie acceptance to an applicable program or an expressly agreed project criterion. [1][3]

Advertisement

Separate distribution repairs from scheduling changes

A runtime change is not a substitute for a pressure or coverage repair. Require separate equipment and scheduling findings, consistent with DOE’s distinction between scheduling, repair and technology-replacement improvements. [1][3]

  • Equipment or design: Leaks, broken or misaligned heads, poor spacing, misting, pressure outside manufacturer specifications, incompatible replacement components and misplaced drip emitters belong on the repair side. Request the affected zone and supporting observation or measurement. [1][3][5]
  • Scheduling: Excessive runtime or frequency, settings unchanged with season or weather, watering after rain, and missing cycle-and-soak where soils or slopes warrant it belong on the scheduling side. Request the proposed adjustment and site-specific rationale. [1][3][5]
  • Mixed findings: Runoff needs investigation rather than an automatic runtime cut. Request observations of pressure, coverage, slope, soil and operating settings to explain whether repairs, scheduling changes or both are proposed. [1]
Advertisement

For pressure findings, request the measured pressure beside the emission-device manufacturer’s specification—not merely a recommendation to water longer or less often. EPA advises checking pressure against manufacturer specifications. [1] The 2009 Version 1 audit guidelines used a ±10% pressure criterion within their historical program scope. That older value is neither a universal existing-facility tolerance nor a claim about current Version 2.0 certification requirements. [2][6]

Keep proposed repairs and proposed scheduling changes separate in the report. Uneven application can lead operators to water for the driest spot, overwatering other areas; identifying the distribution defect matters before settling on a revised schedule. [1]

Advertisement

Request prioritized corrections before approving replacement

Make a zone-by-zone correction list part of the purchased scope. For each item, request:

  • Zone ID and observed defect.
  • Supporting measurement or site observation.
  • Proposed action and priority rationale.
  • Verification method for confirming the correction.

This format and its priority rankings are purchasing terms, not a universal ranked deliverable established by EPA or DOE guidance. [1][3]

Ask the auditor to flag active leaks and broken components for prompt action, separately from coverage corrections, scheduling adjustments and technology proposals. EPA’s landscape checklist recommends flagging defects, while DOE calls for immediate problem reporting and repair within maintenance programs. [3][5]

Before approving controller replacement, request the specific scheduling or control limitation it would address and the distribution defects that would remain. EPA and DOE treat technology selection alongside system assessment, maintenance and scheduling—not as a substitute for them. [1][3]

Do not treat projected savings as guaranteed. Require any site-specific forecast to identify its measurement basis, assumptions and weather context so it can be assessed against actual performance. [1][3]

Advertisement

Define the post-repair check when buying the audit

Put follow-up verification in the scope before authorizing work: name the corrected zones to reinspect, measurements to repeat and before-and-after comparison to deliver. These are purchasing terms built around EPA’s and DOE’s performance and maintenance guidance. [1][3]

  • Leaks and alignment: Operate affected zones to check repaired components for leaks, corrected sprinkler aim, coverage and unwanted watering of pavement or other non-target areas. [3][5]
  • Pressure: Repeat readings in affected zones and compare them with manufacturer specifications—not simply confirmation pressure changed. [1][3]
  • Distribution: Agree which coverage repairs warrant repeat catch-can measurements and which zones will be tested. EPA calls for evaluating uniformity as part of a full audit. [1]
Advertisement

For a useful comparison, specify matching zone identifiers and methods, recorded operating and weather conditions, and before-and-after results. Request disclosure of changed test conditions rather than treating unlike measurements as proof of improvement.

Keep schedule verification separate: request revised settings, their fit with climate, soil, plants, slope and season, and provision for adjustment as weather changes. [1][3]

The cited EPA and DOE guidance does not establish a mandatory post-repair catch-can retest, universal retest interval or numerical acceptance threshold. Specify those terms where needed, alongside the continued periodic monitoring DOE recommends. [1][3]

Choose an auditor who commits to the written scope

Check relevant competency as well as deliverables. EPA labels professional certification programs—not individual professionals directly. Certified Landscape Irrigation Auditor (CLIA) covers general landscape field measurements, maintenance recommendations and basic scheduling; Certified Golf Irrigation Auditor (CGIA) focuses on golf courses. These credentials are not identical service packages. [4]

Advertisement

Ask the provider to disclose involvement in the system’s design, installation or equipment sales. Independence is not a universal mandate established by these sources: the historical 2009 Version 1 guidelines preferred an independent auditor and required disclosure when the auditor also designed or installed that system. Specify any independence or disclosure terms needed for your own procurement, and confirm current certification rules separately. [2][6]

Before selecting a proposal, confirm these purchasing commitments in writing:

  • Coverage: Named zones, irrigation types and exclusions.
  • Baseline: Records, measurements and settings documented before changes.
  • Testing: Stated methods and evaluation criteria.
  • Recommendations: Separate repair and scheduling actions, with prioritized corrections.
  • Verification: Agreed follow-up measurements and checks.

Select a proposal that commits to those outputs rather than an inspection or controller recommendation without the requested evidence.

References

  1. US EPA — WaterSense at Work, Section 5.2: Irrigation (2023) (epa.gov)
  2. US EPA — Guidelines for Irrigation Audits on WaterSense Labeled New Homes, Version 1 (2009; historical) (epa.gov, 2009)
  3. Best Management Practice #5: Water-Efficient Irrigation | Department of Energy (energy.gov)
  4. Professional Certification | US EPA (epa.gov)
  5. US EPA — Find It, Flag It, Fix It: Landscape Irrigation Checklist (archived) (epa.gov)
  6. US EPA — WaterSense Homes Specification Background, Versions 1 and 2 (epa.gov, 2019)
Advertisement

Similar reads