Laser shaft alignment: compare for Australian maintenance teams
Compare Aquip, BRE and Neverstop Water
Compare pump-and-motor laser alignment quotes on soft-foot work, agreed thermal targets and handover evidence: Neverstop Water explicitly includes soft-foot corrections, BRE specifies before-and-after readings, and Aquip offers a tailored completion report.[3][2][1]

Make asset and access details, mounting investigation, approved cold targets and post-torque readings part of the base scope. Specify operating-condition verification separately where required; Reliability Solutions’ field guide distinguishes it from cold, stationary alignment.[4]
Aquip
- Soft-foot work: Ask Aquip to include investigation and correction in the quotation.[1]
- Thermal targets: Ask for written agreement to apply the approved OEM or plant cold targets rather than assuming thermal compensation is included.[1]
- Handover evidence: Aquip promises a completion Laser Alignment Report tailored to customer requirements. Agree its contents before ordering.[1]
BRE Services
- Soft-foot work: Ask BRE to itemise investigation and correction.[2]
- Thermal targets: Obtain a written commitment to the approved cold targets rather than assuming thermal compensation is included.[2]
- Handover evidence: BRE records before-and-after readings and supplies them in an alignment report.[2]
Neverstop Water
- Soft-foot work: Neverstop Water explicitly includes soft-foot and base corrections, plus motor-mount adjustment.[3]
- Thermal targets: Ask for agreement to the OEM or plant thermal targets; its stated tolerance confirmation is not an express commitment to those targets.[3]
- Handover evidence: Neverstop Water supplies detailed alignment results and recommendations as evidence the assembly is within the applicable tolerances.[3]
Check geographical fit before comparing totals. Aquip describes Australian coverage and local or offshore mobilisation; BRE expressly serves Melbourne and Victoria.[1][2] Ask Neverstop Water to confirm attendance at the actual site.[3]
An unconfirmed inclusion is a quotation question, not evidence a contractor cannot perform the work. These descriptions establish starting points, not a ranking.
Send every contractor the same asset and access brief
BRE says duration varies with equipment size and access, so include those details in the enquiry.[2] Give each contractor the same scope:
- Asset details: Identify the driver and driven asset, horizontal or vertical arrangement, operating speed, coupling type and number of coupling planes. Attach relevant drawings and explain whether the work follows installation, repair or a reported problem.[1][2][3][4]
- Coupling access: Describe constraints and ask what access is needed for independent shaft movement. Reliability Solutions warns an engaged coupling can mask soft foot or pipe strain.[4]
- Site responsibilities: Allocate isolation, guarding removal and reinstatement, permits, access equipment, lifting, coupling parts and shims. Ask each contractor to confirm these allocations in writing.[1][2][3]
Have competent site personnel define isolation and operating approvals. BRE’s reference to live production environments is not permission to work on running machinery; Reliability Solutions’ guidance calls for isolation and zero-energy verification.[2][4]
Label the enquiry pump-and-motor shaft alignment. Ask contractors to name and price balancing or additional diagnostics separately from the alignment scope.
Define soft-foot and pipe-strain investigation
Acceptable shaft readings should not close out unresolved mounting problems. Reliability Solutions distinguishes parallel soft foot—a gap—from angled soft foot caused by uneven contact, springy soft foot caused by debris or compressible material, and induced soft foot caused by external loads such as piping or conduit.[4]
Separate checking, diagnosing, correcting and reporting in the quotation. Neverstop Water’s explicit soft-foot and base corrections provide a starting point; define the authorised extent of repairs.[3] Agree an escalation and variation process for base damage or external loads beyond that scope, rather than treating further shimming as automatic acceptance.[4]
Ask how suspect readings will be validated and documented. Reliability Solutions explains that laser routines infer soft foot from shaft movement: they do not directly establish foot planarity or measure pipe strain, and can misdiagnose bent-foot or twisted-base conditions. The guide recommends physical validation with feeler gauges.[4]
Ask each contractor to confirm whether pipe-strain measurement and correction are included.[1][2][3] Put these questions into the enquiry:
- Assessment: Is pipe-strain investigation included, and what findings will be recorded?
- Authority: Who approves intrusive investigation and additional work?
- Remediation: Who owns piping-support corrections, and who decides whether alignment can proceed? Reliability Solutions calls for correcting the external load rather than compensating with machine shims.[4]
Agree thermal targets and tolerances before work
Agree what the cold alignment should achieve. Reliability Solutions defines alignment at normal operating speed and temperature—not simply with the machine cold and stationary. Different thermal movement in the pump, motor and piping may require an intentional cold offset rather than a zero-offset target.[4]
Use OEM thermal targets as the starting point where available. The guide describes thermal-growth calculations as a fallback; require engineering agreement on their inputs and applicability rather than adopting a generic value. OEM or plant requirements take precedence over the guide’s general tolerance guidance.[4]
Put a target schedule into the agreed scope, recording:
- The applicable OEM document and revision, or plant engineering approval.
- Cold target values, units and offset directions.
- The operating temperatures and conditions assumed.
- Acceptance tolerances and who approves departures.
This separates the intended thermal offset from acceptable alignment error.[4] Ask each contractor to confirm the required OEM thermal targets and numerical acceptance tolerances in writing.[1][2][3]
If reliable targets are unavailable, require an engineering decision before acceptance: investigate further or separately scope operating-condition verification. Reliability Solutions identifies offline-to-running measurement as an option for critical or unfamiliar assets.[4]
Make post-torque readings the acceptance checkpoint
Use the post-torque reading—not an earlier successful measurement—for acceptance. Reliability Solutions explains that tightening hold-down bolts can shift alignment, so final readings should follow manufacturer-specified bolt torque and demonstrate compliance with the agreed target and tolerances.[4]
Put the sequence into the work order at a contractual level: record the as-found condition, resolve agreed mounting issues, apply the approved target, make corrections, complete final bolt torque and remeasure. The guide supports this sequence and retaining as-found/as-left records.[4]
Ask the provider to identify which measurement is the accepted as-left result. Require a record of corrections, unresolved defects and approved scope changes; nominate who can authorise exceptions. Agree that subsequent disturbance to the alignment triggers a recheck before acceptance. Write these provisions into the scope rather than assuming they are standard terms.
Specify the report and separate operating verification
Ask for a sample report before award, then put the agreed fields into the purchase order. Use this checklist, drawing on Reliability Solutions’ documentation guidance:[4]
- Asset identification, work-order number, date and technician.
- As-found readings and final, post-torque as-left readings.
- Ambient temperature, applied thermal target and agreed acceptance tolerances.
- Corrections completed and unresolved pipe-strain or base issues.
Aquip’s report tailoring, BRE’s before-and-after readings and Neverstop Water’s results and recommendations are different reporting commitments; agree the required fields rather than relying on the report’s title.[1][2][3]
Static acceptance is not operating verification. A cold, stationary report records alignment against the stated target; it does not by itself demonstrate alignment under loaded, operating-temperature conditions.[4] Neverstop Water’s rotation verification is not an express commitment to a loaded hot-state test.[3] Ask each contractor to itemise offline-to-running (OLTR), post-start vibration or motor-current verification where required.[1][2][3]
If required, specify operating verification separately, with site-approved conditions, assigned responsibilities, evidence and acceptance criteria. Reliability Solutions describes OLTR as assessing movement associated with steady-state operation and using that evidence to refine the cold target—not simply issuing another static report.[4]
Compare itemised quotes and commercial terms
Ask Aquip, BRE and Neverstop Water for prices, call-out or travel charges, minimum order values and cancellation fees before comparing quotes.[1][2][3]
Request itemised quotes covering labour, travel, consumables, approved corrections, reporting and optional operating verification. Ask for GST treatment, exclusions and variation approval to be explicit rather than comparing headline totals alone.
Get attendance commitments, cancellation terms, insurance evidence, relevant technician competence and any workmanship or alignment-hold warranty in writing. These are quotation questions, not evidence a contractor lacks cover, competence or a warranty.
Aquip advertises short-notice mobilisation and 24-hour availability, not a guaranteed attendance deadline.[1] BRE says duration depends on equipment size and access.[2] Ask each contractor to distinguish agreed attendance time from estimated job duration.
Choose on the accepted scope
Before award, check the quotation accepts the asset and access brief, investigation and correction responsibilities, engineering-approved targets, post-torque acceptance readings and agreed reporting. Keep operating verification separately scoped and priced where required.[4]
Return incomplete quotes for clarification. Carry the accepted scope and acceptance schedule into the purchase order so the contractor and site team are working to the same requirements.
References
- Laser Shaft Alignment Services Australia | Aquip (aquip.com.au)
- Laser Alignment Services Melbourne | BRE Services (breservices.com.au)
- Pump & Motor Shaft Alignment | Neverstop Water Sydney NSW (nswater.com.au, 2026)
- Precision Laser Alignment : The complete field guide for industrial maintenance teams – Reliability Solutions (reliabilitysolutions.net)