How to Choose Acoustic Emission Testing for US Vessel Owners
Start with a written screening scope
Choose an acoustic emission testing service by confirming asset eligibility and agreeing on loading, demonstrated sensor coverage, noise controls, targeted follow-up and acceptance responsibility before commissioning. Separate the proposed screening work from any asset-specific code or regulatory acceptance.

Acoustic emission (AE) passively detects transient elastic waves released by active changes in material under stress. Dormant flaws may produce no detectable activity, so a quiet test cannot establish that a vessel is flaw-free. [2]
Keep three outputs separate in the scope:
- Screening: recorded activity and inferred source locations within the test’s coverage and detection limits—not a complete description of every flaw. [2]
- Targeted complementary inspection: closer examination of areas identified by AE. ASNT describes this follow-up role rather than treating screening as the endpoint. [2]
- Engineering acceptance: identify the responsible decision-maker separately from the screening interpretation. ABS’s 2016 marine/offshore guidance distinguishes reporting, follow-up and verification, and calls for qualified professional assessment. [4]
The National Board’s account of a 1988 presentation describes written procedures covering the examination object, material, equipment, parameters, recording and personnel. Its editor warns that requirements may have changed and directs readers to the latest applicable ASME code; use the account as historical context, not current authority. [5]
Check asset eligibility and site availability
Send the prospective inspector the vessel type, material, geometry, service, target damage, site location and intended objective: screening or requalification. Ask for written confirmation that the proposed service fits the application; AE planning depends on the asset, its condition and the flaws being investigated. [2][4]
MISTRAS MONPAC illustrates the process-vessel scope check. MISTRAS describes MONPAC for metallic pressure vessels, spheres, columns and tanks, with applications during first hydrotests, requalification hydrotests and in-service pressurization with working fluid. [1] Ask MISTRAS to confirm availability at your US site. [1]
FIBA illustrates the high-pressure equipment eligibility check. FIBA describes AET for high-pressure tubes and vessels, including still-assembled tube trailers. It describes its US locations as DOT-authorized requalification facilities and offers a Mobile Pressure Vessel Tester operating throughout the United States. [3] Ask FIBA to identify the exact equipment it will accept and the proposed requalification basis rather than extending that service description to every process-vessel application.
Use these service descriptions to frame eligibility questions, not as interchangeable packages. ASNT supplies method background, ABS supplies marine/offshore guidance, and the National Board article supplies historical technical context—not alternative field-inspection offers. [2][4][5]
Agree on loading and operational responsibilities
Record the target damage and available pressure or loading history before selecting the test condition. AE detects active changes under applied or operational loading; an inactive flaw may produce no useful signal. [2]
The National Board account explains why prior loading matters: under the Kaiser effect, detectable activity may not resume until a previously applied pressure is reached. This is planning context, not an instruction to exceed previous pressure. [5]
Have the qualified team obtain asset-specific approval for the proposed test condition and document:
- Loading plan: the sequence, monitoring stages and authorized operating boundaries, informed by the vessel’s history and the damage being sought. [2][5]
- Operational responsibilities: who operates the vessel, supplies loading equipment and utilities, coordinates access and authorizes interruptions.
- Stop and restart authority: who can halt loading, investigate abnormal activity and authorize a restart after corrective action. The National Board account describes safe investigation and corrective action before resuming after termination-related concerns. [5]
Obtain qualified approval of the limits and sequence rather than borrowing pressure percentages or another vessel’s procedure. ABS describes application-specific planning and collaboration among the owner/operator, test team and classification society in its marine/offshore context. [4]
Require demonstrated sensor coverage
Request a sensor-layout drawing showing the monitoring area, sensor positions, inaccessible regions, geometry constraints and exclusions. ASNT notes that complex geometry can complicate sensor placement. [2]
ASNT describes large-area coverage from a single setup and source location using multi-sensor signal arrival times. [2] Attenuation determines how far acoustic waves travel and influences sensor spacing; wave velocity supports location calculations using differences in arrival time at the sensors. [2]
Request on-vessel simulated-event checks as evidence for the arrangement. The National Board account describes determining spacing using simulated events away from mounted sensors, with spacing also dependent on the location method. It describes channel-performance checks after installation and before sensor removal. [5] Ask the inspector to identify the checks and acceptance criteria applicable to the proposed procedure rather than borrowing historical numerical requirements.
MISTRAS advertises “100% inspection” during one pressure test. Treat that as a vendor coverage claim requiring asset-specific demonstration, not certainty of detecting every flaw: ASNT notes that inactive flaws may produce no detectable activity. [1][2]
Ask for the final report to retain the installed layout, coverage-check results and exclusions alongside the event map so reviewers can interpret locations against the demonstrated arrangement.
Set noise controls and inconclusive-test conditions
Require the proposal to explain how the team will measure background noise, control interference and flag unusable data. ASNT identifies background noise and environmental vibration as limitations; the National Board account gives examples including motors, rubbing cables, piping and nearby pumps. [2][5]
Separate detection from evaluation. The National Board account distinguishes the adjustable examination threshold, at which a channel detects a signal, from the evaluation threshold used to evaluate activity. [5] Ask the inspector to identify both settings and their basis in the proposed procedure. The account does not establish universally applicable noise thresholds, warning levels or retest intervals. [5]
Put warning, stop, corrective-action and retest conditions in writing. Require them to address excessive noise, unusual signal behavior, interrupted loading and incomplete coverage—including when the result should remain inconclusive. The National Board account advises against examination with excessive sensor noise. [5]
Require the interpretation to acknowledge dormant defects, material sensitivity, complex geometry and signal-analysis limitations. Signal amplitude alone does not necessarily establish damage severity. [2]
Specify the evidence package and targeted follow-up
Require more than an event map. ASNT describes AE as a way to identify areas needing closer examination. Source location is inferred through the configured sensor system; a plotted indication does not itself establish defect size or shape. [2][6]
Put these deliverables in the written scope:
- Test identity and loading: asset identification, procedure used and the actual loading record linked to recorded activity.
- Measurement evidence: installed sensor layout, demonstrated coverage, channel-check results and noise-related limitations.
- Findings and boundaries: event locations, interpretation, exclusions, unresolved areas and recommended follow-up.
These requests build on the National Board account’s discussion of recording and documentation, ASNT’s method limitations, and ABS’s reporting and follow-up stages. [2][4][5]
For each indication requiring investigation, request a traceable entry linking its identifier and vessel location to the reason for follow-up, the selected complementary method and the responsible party. The National Board account describes using mapped areas to direct other nondestructive examinations. [5]
Have a qualified inspector select the follow-up method for the suspected damage. Switzerland-based equipment vendor Voliro discusses ultrasonic testing for additional defect characterization; its article is background, not an offer of vessel AE screening or a universal follow-up prescription. [6]
Agree beforehand how contradictory follow-up findings will trigger reassessment. Require noisy or incompletely covered regions to remain explicitly unresolved, with an assigned action. Request complementary inspection results, revised interpretations and remaining limitations in the final package, consistent with the separate reporting, follow-up and verification stages in ABS’s guidance. [4]
Name the acceptance criteria and approving parties
Before data collection, document the asset-specific code or regulatory basis, applicable edition, evaluation criteria and approving parties. The National Board account places evaluation criteria and personnel requirements under the referencing code section, but does not verify today’s requirements. [5]
Allocate these responsibilities explicitly:
- AE interpretation: who evaluates recorded activity against the agreed procedure and reports limitations.
- Complementary inspection: who investigates indicated areas and reports the findings.
- Final approval: who makes the engineering acceptance decision and obtains any applicable regulatory or classification acceptance.
Ask for qualification and certification evidence relevant to the proposed work. ASNT describes AE Level III certification; the National Board account separately identifies project-specific personnel requirements under the referencing code section. [2][5]
MISTRAS describes MONPAC severity color coding and recommendations. Treat these as vendor interpretation tools, not independent proof of asset-specific acceptance. [1] Neither MISTRAS’s nor FIBA’s cited service page assigns final fitness-for-service approval or engineering liability contractually; request that allocation explicitly. [1][3]
An AE “pass” should not be treated as automatic permission to continue operation. The service descriptions and guidance do not establish a universal substitute for internal inspection, an inspection-interval extension or regulatory approval. [1][3][4][5]
Request a scope-based quote
Send prospective inspectors the same written scope and request explicit inclusions, exclusions and responsibilities. Ask for screening to be priced separately from mobilization, access preparation, operational support, complementary inspection and repeat visits. These are requested quote categories, not confirmed provider charges.
Request duration, minimum commitment, cancellation terms and responsibility for costs if testing is inconclusive or repeated. Ask MISTRAS and FIBA to confirm fixed prices, test duration, minimum terms and cancellation conditions in writing. [1][3]
Before commissioning, resolve gaps in asset eligibility, loading arrangements, demonstrated coverage, noise contingencies, follow-up evidence and final approval responsibility. Return unresolved items for clarification rather than accepting an undefined screening scope.
References
- MONPAC Inspection Services | MISTRAS Group | MISTRAS Group (mistrasgroup.com)
- Acoustic Emission Testing (AE): NDT Structural Monitoring & Flaw Detection (asnt.org)
- Acoustic Emission Testing (AET) – FIBA Technologies, Inc. (fibatech.com)
- Guidance Notes on Structural Monitoring Using Acoustic Emissions (eagle.org)
- Acoustic Emission Examination of Metal Pressure Vessels (nationalboard.org)
- Acoustic Emission Testing: Process & Equipment | Voliro (voliro.com)